Etc SmartFade v3.0.1 Manual de usuario Pagina 79
- Pagina / 84
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
A 73
Appendix A
Software Update
This appendix contains the instructions for updating the software in your SmartFade
console. There are two ways of updating the software.
• Using the SD card
• Connecting with USB to a PC
Software can be downloaded from the ETC Web site: www.etcconnect.com
Please make sure to download the correct software for your console - SmartFade and
SmartFadeML use different software.
To verify the version that your console is running, See “Software Version” on page 25.
CAUTION:
Make sure to back up any show data you want to keep to the SD card before
proceeding with a software upgrade.
CAUTION:
Only standard SD Memory cards or connection to a PC via USB may be used for
updating the software on a SmartFade console. Software update is not possible
using an SDHC Memory card.
Update the Software
SD Card Update
If you are using an SD card for the very first time - make sure it is formatted correctly
(FAT16), or it will not function with SmartFade. See “Format SD Memory Card” on page 7.
Step 1: Obtain the software update file SMRTFADE.SRC from the download section of
the ETC Web site: www.etcconnect.com
Step 2: Copy the SMRTFADE.SRC file to the root directory of the SD card. DO NOT
RENAME THE FILE!
Step 3: Start the console in test mode. This is done by holding down the MENU button
and pressing once on ON.
The unit will enter self-test mode. Press MENU for each of the tests until the
memory test has completed. At the end of the memory test the display will
prompt:
Firmware Upgrade
Are you sure? [No]
Step 4: Insert the SD card into the console.
Step 5: Turn the encoder to select YES and press MENU. The update will start and the
console will boot into the new updated software after the process is complete.
- Control Console 1
- User Manual 1
- Table of Contents 3
- Chapter 4 4
- Chapter 5 5
- Chapter 6 5
- Chapter 7 5
- Appendix A 6
- Introduction 7
- Using this Manual 8
- Americas 9
- United Kingdom 9
- Unpack & Connect 10
- Power-up Procedure 10
- Shutdown Procedure 10
- Operating Modes 11
- Save Show to card 12
- Format SD Memory Card 13
- Load show from card 13
- Load patch from card 13
- General Information 15
- Control Capacity 16
- Frontpanel Functionality 17
- Faders & Bump buttons 18
- Independents 18
- Crossfader 18
- 1 General Information 13 19
- Record & Edit functions 19
- LCD & Wheel Functions 20
- Philosophy of the Console 21
- Data Structure & Timing 22
- Chapter 2 23
- DMX Output 24
- Clear/Set Patch 25
- Patch Dimmers 26
- 2 Setup 21 27
- Patch by Channel 27
- Patch Independents 28
- Console Settings 29
- Language 30
- 2 Setup 25 31
- Disable Recording 31
- Crossfade faders 31
- Software Version 31
- MIDI Setup 32
- 2 Setup 27 33
- Synchronising Two SmartFades 33
- Basic MIDI implementation 33
- MIDI Channel 34
- Chapter 3 35
- Intensity channels 36
- 3 Program 31 37
- Adjust Channel Range 37
- Set Channel Range 37
- Memories 38
- 3 Program 33 39
- Record a Magic memory 39
- Snapshots 40
- 3 Program 35 41
- Copy a Snapshot to a Memory 41
- Sequences 42
- 3 Program 37 43
- Record a Sequence 43
- Record a Magic Sequence 44
- 3 Program 39 45
- Record the Stack from bumps 46
- 3 Program 41 47
- Record a Stack state 48
- Edit Memories 50
- Edit Sequences & Stack 51
- Delete a Step 52
- 4 Edit 47 53
- Insert a Step 53
- Insert a PointQ 54
- 4 Edit 49 55
- Change the content of a Step 55
- 4 Edit 51 57
- Copy a Sequence 57
- Run Modes 57
- Sequence & Stack Times 58
- 4 Edit 53 59
- Global Time for all steps 60
- Playback 61
- General Functions 62
- 5 Playback 59 65
- Stack & Crossfader 66
- 5 Playback 61 67
- Rate & Fade for the Stack 67
- Tap Mode for the Stack 68
- 5 Playback 63 69
- Single Scene Crossfading 69
- Two Scene Mode 71
- Two Scene Fading 73
- DMX Backup 75
- Backup memories 77
- Stack in Backup Mode 78
- Software Update 79
- USB Update 80
Relacionado con productos y manuales para Panel De Control Etc SmartFade v3.0.1
(1 paginas)
(1 paginas)
(80 paginas)
Panel De Control Etc Congo Family v6.4 Manual de usuario
(102 paginas)
(102 paginas)
Panel De Control Etc Element v2.1.0 Manual de usuario
(318 paginas)
(318 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales