Etc SmartFade v3.0.1 Manual de usuario Pagina 62
- Pagina / 84
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
56 SmartFade v3.0.1 User Manual
General Functions
Master & Black Out function
To get light output (at all), the Master needs to be at full, and the Black Out button off.
The Master fader proportionally limits all intensity outputs. As soon as the Master is faded
under 100% the Blackout button will blink.
The Blackout button instantly sends all intensity outputs to zero. As soon as it is activated
the button will light up.
Note:
The Independent channels patched to IND 1 and IND 2 are not affected by the Master
fader or Black Out button unless they are set to “GM” in the Independent Settings. See
“Set up Independents” on page 22.
Light output from the intensity faders is also affected by the NEXT button. See “Intensity
channels” on page 30.
Clear
Clear is a very useful button that will bring you back to a “clean” state of the console with
no output. Pressing CLEAR will NEVER erase content - it only brings the fader intensities
to zero. You can press CLEAR to abort any recording function if it is blinking.
• Set all dimmer intensities from channel faders and Stack to zero . . = 2 presses
• Set all memory faders to zero (blackout) . . . . . . . . . . . . . . . . . . . . . = 3 presses
• Set sequence faders to zero (blackout) . . . . . . . . . . . . . . . . . . . . . . = 4 presses
CLEAR is also used in combination with other keys. For example
Bump Master
The Bump Master sets the level to which bump buttons will flash. See Bump Button
functionality for each type of fader mode.
Action Console Feedback
Clear intensities 1-24 and All intensities 1-24 are cleared.
Clear intensities 25-48 and All intensities 25-48 are cleared.
Clear intensities 1-48 and All intensities 1-48 are cleared.
Clear intensities 49-96 and All intensities 49-96 are cleared.
Clear Stack and The Stack is cleared and set to zero.
Clear Snapshots and All Snapshots are cleared, and the counter is
set to 1.
Clear Rate and All Rate settings are cleared.
BLACK
OUT
CLEAR
1-24
CLEAR
25-48
CLEAR
1-48
CLEAR
49-96
CLEAR
CLEAR
SNAP
SHOT
CLEAR
RATE
- Control Console 1
- User Manual 1
- Table of Contents 3
- Chapter 4 4
- Chapter 5 5
- Chapter 6 5
- Chapter 7 5
- Appendix A 6
- Introduction 7
- Using this Manual 8
- Americas 9
- United Kingdom 9
- Unpack & Connect 10
- Power-up Procedure 10
- Shutdown Procedure 10
- Operating Modes 11
- Save Show to card 12
- Format SD Memory Card 13
- Load show from card 13
- Load patch from card 13
- General Information 15
- Control Capacity 16
- Frontpanel Functionality 17
- Faders & Bump buttons 18
- Independents 18
- Crossfader 18
- 1 General Information 13 19
- Record & Edit functions 19
- LCD & Wheel Functions 20
- Philosophy of the Console 21
- Data Structure & Timing 22
- Chapter 2 23
- DMX Output 24
- Clear/Set Patch 25
- Patch Dimmers 26
- 2 Setup 21 27
- Patch by Channel 27
- Patch Independents 28
- Console Settings 29
- Language 30
- 2 Setup 25 31
- Disable Recording 31
- Crossfade faders 31
- Software Version 31
- MIDI Setup 32
- 2 Setup 27 33
- Synchronising Two SmartFades 33
- Basic MIDI implementation 33
- MIDI Channel 34
- Chapter 3 35
- Intensity channels 36
- 3 Program 31 37
- Adjust Channel Range 37
- Set Channel Range 37
- Memories 38
- 3 Program 33 39
- Record a Magic memory 39
- Snapshots 40
- 3 Program 35 41
- Copy a Snapshot to a Memory 41
- Sequences 42
- 3 Program 37 43
- Record a Sequence 43
- Record a Magic Sequence 44
- 3 Program 39 45
- Record the Stack from bumps 46
- 3 Program 41 47
- Record a Stack state 48
- Edit Memories 50
- Edit Sequences & Stack 51
- Delete a Step 52
- 4 Edit 47 53
- Insert a Step 53
- Insert a PointQ 54
- 4 Edit 49 55
- Change the content of a Step 55
- 4 Edit 51 57
- Copy a Sequence 57
- Run Modes 57
- Sequence & Stack Times 58
- 4 Edit 53 59
- Global Time for all steps 60
- Playback 61
- General Functions 62
- 5 Playback 59 65
- Stack & Crossfader 66
- 5 Playback 61 67
- Rate & Fade for the Stack 67
- Tap Mode for the Stack 68
- 5 Playback 63 69
- Single Scene Crossfading 69
- Two Scene Mode 71
- Two Scene Fading 73
- DMX Backup 75
- Backup memories 77
- Stack in Backup Mode 78
- Software Update 79
- USB Update 80
Relacionado con productos y manuales para Panel De Control Etc SmartFade v3.0.1
(1 paginas)
(1 paginas)
(80 paginas)
Panel De Control Etc Congo Family v6.4 Manual de usuario
(102 paginas)
(102 paginas)
Panel De Control Etc Element v2.1.0 Manual de usuario
(318 paginas)
(318 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales