Etc SmartFade v3.0.1 Manual de usuario Pagina 18
- Pagina / 84
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
12 SmartFade v3.0.1 User Manual
Faders & Bump buttons
There are 24 (48) faders. They can be set to control intensities or memories and
sequences. These modes are set with the FADERS buttons.
or
Each fader has a Bump button below it. This button will light up when there is content, and
it will mimic the output of the content by varying its intensity. The button color will vary
depending on the type of content.
... or ...
Bump Playback Modes
There are two Bump modes when a Bump button is pressed, Pile-on and Solo. Both use
the level of the BUMPS fader. The SOLO button toggles between these modes. See “Bump
Master” on page 56.
Note:
For intensity faders to control light output live, three things are required:
- The Master Fader is over zero, and normally set to full (the topmost position).
- The BLACKOUT button is off (not lit)
- The NEXT button is off (not lit).
Master & Black Out function
The Master fader proportionally limits all intensity outputs. The Blackout button instantly
sends all intensities generated by the console to zero. See “Master & Black Out function”
on page 56.
Independents
The two Independent buttons are separate control channels (IND 1, IND 2) that can control
any outputs in a toggle or bump mode. These outputs can be separated from all other
controls. See “Set up Independents” on page 22.
Crossfader
The Crossfader consists of a Live and Next fader, plus the Crossfade transport buttons. It
can be used for fading between the 199 steps of the programmable Stack, or for single-
scene fading into intensities that are set blind in NEXT mode. Stack & Crossfader, page 60
The following buttons are used together with the crossfader
1-24
25-48
1-48
49-96
1
24
1
48
SOLO
BLACK
OUT
IND
1
IND
2
NEXT
STACK
- Control Console 1
- User Manual 1
- Table of Contents 3
- Chapter 4 4
- Chapter 5 5
- Chapter 6 5
- Chapter 7 5
- Appendix A 6
- Introduction 7
- Using this Manual 8
- Americas 9
- United Kingdom 9
- Unpack & Connect 10
- Power-up Procedure 10
- Shutdown Procedure 10
- Operating Modes 11
- Save Show to card 12
- Format SD Memory Card 13
- Load show from card 13
- Load patch from card 13
- General Information 15
- Control Capacity 16
- Frontpanel Functionality 17
- Faders & Bump buttons 18
- Independents 18
- Crossfader 18
- 1 General Information 13 19
- Record & Edit functions 19
- LCD & Wheel Functions 20
- Philosophy of the Console 21
- Data Structure & Timing 22
- Chapter 2 23
- DMX Output 24
- Clear/Set Patch 25
- Patch Dimmers 26
- 2 Setup 21 27
- Patch by Channel 27
- Patch Independents 28
- Console Settings 29
- Language 30
- 2 Setup 25 31
- Disable Recording 31
- Crossfade faders 31
- Software Version 31
- MIDI Setup 32
- 2 Setup 27 33
- Synchronising Two SmartFades 33
- Basic MIDI implementation 33
- MIDI Channel 34
- Chapter 3 35
- Intensity channels 36
- 3 Program 31 37
- Adjust Channel Range 37
- Set Channel Range 37
- Memories 38
- 3 Program 33 39
- Record a Magic memory 39
- Snapshots 40
- 3 Program 35 41
- Copy a Snapshot to a Memory 41
- Sequences 42
- 3 Program 37 43
- Record a Sequence 43
- Record a Magic Sequence 44
- 3 Program 39 45
- Record the Stack from bumps 46
- 3 Program 41 47
- Record a Stack state 48
- Edit Memories 50
- Edit Sequences & Stack 51
- Delete a Step 52
- 4 Edit 47 53
- Insert a Step 53
- Insert a PointQ 54
- 4 Edit 49 55
- Change the content of a Step 55
- 4 Edit 51 57
- Copy a Sequence 57
- Run Modes 57
- Sequence & Stack Times 58
- 4 Edit 53 59
- Global Time for all steps 60
- Playback 61
- General Functions 62
- 5 Playback 59 65
- Stack & Crossfader 66
- 5 Playback 61 67
- Rate & Fade for the Stack 67
- Tap Mode for the Stack 68
- 5 Playback 63 69
- Single Scene Crossfading 69
- Two Scene Mode 71
- Two Scene Fading 73
- DMX Backup 75
- Backup memories 77
- Stack in Backup Mode 78
- Software Update 79
- USB Update 80
Relacionado con productos y manuales para Panel De Control Etc SmartFade v3.0.1
(1 paginas)
(1 paginas)
(80 paginas)
Panel De Control Etc Congo Family v6.4 Manual de usuario
(102 paginas)
(102 paginas)
Panel De Control Etc Element v2.1.0 Manual de usuario
(318 paginas)
(318 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales